Start with what is installed
Factory System Overview
Speaker upgrades can be planned without replacing the factory receiver. That is especially useful with Bang & Olufsen equipment, where retaining the original receiver is the recommended approach and the center speaker, rear coaxials and subwoofer require package-specific attention.
Factory receiver choices include a mono-LCD unit, a 4.2-inch LCD and an 8-inch display. Receiver-removal coverage here is limited to the 4.2-inch version and select 8-inch configurations; it does not establish a replacement procedure for the mono-LCD unit.
The standard six-speaker arrangement uses front components and full-range rear-door speakers. The optional ten-speaker Bang & Olufsen system adds a center dash speaker, rear-door coaxials and a small subwoofer. The factory speaker count includes the separate drivers within the rear coaxials.
The factory amplifier is behind the rear seat and can be reached by folding the seatback. Confirm the actual amplifier and channel arrangement before adding equipment; access to an amplifier does not establish a universal bypass or connection method.
Planning guide, not a fitment guarantee. Exact wiring, impedance, adapters, fasteners and removal procedures must match your vehicle. Photographs show selected configurations, not universal fitment.
Radio Upgrade
Receiver replacement involves several dashboard-disassembly stages, so keep the fasteners and connectors organized. Use a dash kit, wiring interface and instructions verified for the specific display and equipment combination.
Replacing the standard receiver loses the factory rearview-camera function in the documented configuration. Plan a verified compatible camera solution rather than assuming the original camera will continue working.
The 8-inch display incorporates climate controls. Only some configurations support replacement, and preserving climate operation must be part of the selected integration package. Retain the original receiver in Bang & Olufsen vehicles rather than applying a standard-radio procedure to that system.
Radio access and installation
- Identify the display, audio package and cab style, and record which factory functions need to remain.
- For a supported 4.2-inch or select 8-inch installation, obtain the exact dash-kit and harness instructions before removing panels.
- Work through the configuration-specific disassembly sequence, labeling plugs and keeping removed screws with their original panels.
- After installation, test every speaker, climate-control function and the planned camera solution before restoring the dashboard.
Check before reassembly
Test the receiver and every speaker channel before refitting trim. Confirm nearby switches, climate controls and vents remain accessible. Keep connectors secure and wiring clear of sharp edges, pedals and moving mechanisms.
Speaker Upgrades
Choose speakers by location and exact factory configuration, not the nominal diameter alone. Check mounting depth, screw pattern, grille clearance and electrical compatibility before ordering.
Front door woofers
Factory speaker size: 6.75-inch
The front door woofers can be replaced with selected 6.5-inch or 6.75-inch drivers. Some choices require mounting brackets, and the space behind the original grille can limit how far a replacement projects.
A component set can address the woofer and sail-panel tweeter together, but the amplifier load and crossover arrangement must suit the original system or the planned replacement electronics.
- Release the sail panel. Remove the cover behind the door-release handle and its Torx T25 screw.
- Release the outer door-pull cover, which has twelve clips, and remove the two exposed Torx T25 screws.
- Remove the two lower-edge Torx T25 screws. Release the side and bottom panel clips, then disconnect the harnesses and release cable.
- Remove the three 7mm speaker screws, unplug the woofer and fit the verified replacement with the required bracket.
Fitment and wiring notes
Some speakers require trimming the back of the plastic grille for clearance. Check the actual fit first; any trimming is permanent and should be done carefully with eye protection.
Check window travel, cable routing and grille clearance before reinstalling the panel.
Front sail-panel tweeters
Factory speaker size: Approximately 1.602-inch physical diameter; high-impedance factory units
The original tweeters sit in the sail panels and are wired in parallel with the door woofers. They are high-impedance units; a 4-ohm replacement can play louder and change the balance relative to the woofers.
The factory physical diameter is not a universal replacement size. A custom mounting solution and secure wiring connections are required because dedicated replacement mounts and plug-in adapters are not established for this location.
- Gently release the sail panel with a panel tool.
- Press the retaining tab to release the original tweeter, then remove it.
- Secure the replacement in a properly fabricated mount and connect it using the appropriate crossover and insulated wiring connections.
Fitment and wiring notes
Do not substitute a lower-impedance tweeter without evaluating amplifier load, crossover protection and front-stage balance.
Rear door speakers — SuperCab
Factory speaker size: 6.75-inch
The SuperCab rear doors contain the rear speakers, but their trim-removal process differs from the larger SuperCrew doors. Plan time to organize the multiple fasteners and follow the correct cab-specific sequence.
Selected 6.5-inch and 6.75-inch replacements are options, with mounting brackets required for some models. The ring behind the door panel may need trimming to clear a taller replacement.
- Use the SuperCab-specific disassembly instructions to remove the rear-door trim and retain each fastener by location.
- Disconnect and remove the factory speaker, then trial-fit the selected bracket and replacement before modifying trim.
- Test the speaker and verify panel clearance before completing reassembly.
Fitment and wiring notes
Do not apply the SuperCrew panel-removal sequence to a SuperCab.
Any required panel-ring trimming is permanent; wear eye protection and remove only the material required by the verified fit.
Rear door speakers — SuperCrew
Factory speaker size: 6.75-inch
The SuperCrew rear speakers are reached by removing the rear door panels. Standard systems use full-range speakers; Bang & Olufsen vehicles use rear coaxials, so confirm the installed package when selecting replacements.
- Remove the rear-door trim following the SuperCrew-specific fastener sequence.
- Disconnect the original speaker and fit the verified replacement with any required mounting bracket.
- Test audio and check the door-release cable, window operation and panel fit before closing the door.
Fitment and wiring notes
A matching nominal size does not establish the correct impedance or integration with Bang & Olufsen amplification.
Center dash speaker — Bang & Olufsen
Factory speaker size: Verify directly; nominal size is not established
The center speaker is specific to the Bang & Olufsen package. Its grille and mounting screws are accessible, but neither a nominal replacement size nor an impedance is established here. Measure and identify the original driver before ordering.
A plug-in wiring adapter is not established for this location. Use properly insulated splices, soldered connections or appropriate speaker-wire connectors when the replacement has been verified.
- Starting at the rear edge, release the center grille’s six clips and lift the grille away.
- Remove the two 7mm screws, disconnect the harness and lift out the speaker.
- Verify the replacement diameter, depth, mounting pattern and electrical load before installing it and restoring the grille.
Fitment and wiring notes
Do not buy a center speaker from an assumed diameter or substitute an arbitrary lower-impedance driver.
Shop Speaker Sizes
Browse the supported categories, then verify fit for your exact location.
Front door woofers
Verify the exact cab, factory audio package, impedance, mounting depth and bracket requirements before ordering.
Front sail-panel tweeters
Verify the exact cab, factory audio package, impedance, mounting depth and bracket requirements before ordering.
Rear door speakers — SuperCab
Verify the exact cab, factory audio package, impedance, mounting depth and bracket requirements before ordering.
Rear door speakers — SuperCrew
Verify the exact cab, factory audio package, impedance, mounting depth and bracket requirements before ordering.
A nominal size match does not establish direct fit. Preserve the configuration-specific cautions in this guide.
Tools and Installation Preparation
- Panel tool
- Small flat-blade screwdriver
- 7mm socket, ratchet and extension
- Torx T25 driver for front and SuperCrew rear door work
- SuperCab rear doors: Torx T20, T25 and T50 drivers
- Utility knife and eye protection only where a verified speaker fit requires plastic trimming
- B&O subwoofer access: Torx T20 driver and 10mm socket
Bass and Amplifier Planning
In Bang & Olufsen-equipped SuperCrew trucks, the factory subwoofer sits behind the rear seat. It is an approximately 6-inch dual-voice-coil driver with a proprietary Ford bolt pattern, not a standard drop-in mounting arrangement.
A replacement approach uses a suitable 5.25-inch woofer with a fabricated bracket. This is a subwoofer application, not a recommendation to install an ordinary 5.25-inch coaxial door speaker. Verify enclosure and amplifier compatibility, mounting depth and electrical load, and use a protective grille at this location.
The factory subwoofer feed contains bass only, so a replacement connected to that feed will not receive full-range audio. The original coil impedance is not established here; do not infer it from the driver size.
There is no straightforward spare enclosure location identified in this cab. A compact powered subwoofer may be possible only by sacrificing some rear legroom. Measure the actual truck, preserve seat and belt operation, and secure any equipment against movement.
Installation Checklist
- Identify display type, cab style and standard versus Bang & Olufsen audio.
- Retain the B&O receiver and do not assume mono-LCD replacement support.
- Verify camera and climate-control consequences before a supported radio conversion.
- Check speaker impedance, crossover integration, brackets and grille clearance.
- Test all speakers and affected vehicle functions before final panel reassembly.
Car audio guides, upgrades and installation planning.
